Power Supplies, Chargers & Wall Transformers
Showing all 119 results
-
VA5H3200
$52.005V 32A Acopian Supply (Store)
-
COL72559
$12.00COLECO DISK DRIVE POWER SUPPLY for ADAM system; transformer type with outputs +5 V 3 amp +12 V 2.9 A -5 V 200 ma and +18 V inductive 1 A. 115 V 60 Hz input. With cords and On-Off switch. 11x4x8 10 lbs sh. unused,
-
PP-4763
$275.00POWER SUPPLY, produces 28 VDC 50 amps from 115 VAC 22 amps 47-63 Hz 22/11 amp input; solid-state with +/-0.5% regulation. With meters 0-50 VDC and 0-80 amps DC; 13.5x 19.5×15, 145 lbs. Used checked
-
LC28T2.1-1
$29.9528VDC 2.1 Amp Power Supply by Abbott. 8.5×4.6×4 13 lbs sh. (L2U) Unused
-
NCR-25
$125.00Industrial Power Supply made for NCR rated 12 volts at 25 amps. These power supplies will easily provide up to 45 amps under normal ham radio usage. 19" x 7" x 16" 70 lbs shipping. (R1M) Used Checked.
-
NCR-5
$50.00Industrial Power Supply made for NCR rated 12 volts at 5 amps. These power supplies will easily provide up to 10 amps under normal ham radio usage. 10" x 7" x 16" 35 lbs shipping. (R1M) Used Checked.
-
PP-6224A/U
$250.00* The PP-6224 power supply allows using vehicular equipment at fixed or airborne locations where AC power is available This is a portable power supply that has two outputs that can supply "24 Volt" power at up to 25 Amps total. It's input can be either AC (115 or 230 VAC & 50 60 or 400 Hz) or a "24 Volt" battery with automatic switchover to the battery if the AC fails. (H2CL1X) Used Checked comes with U-383 connector for you to wire to your own power cord.
-
GLC110-24
$24.95*GLC Series 24 VDC Global Performance Commercial AC/DC Regulated Switching Power Supply, 4.6A 110W peak, 3.2A 75W continuous power output, input voltage 90-264 VAC, output voltage variable +/- 1.5V, output noise 0.5% RMS, overload protected (power limited at 120W). Size 7″ x 4.25″ x 1.3″; 1.2 lb.; We set one to just under 26 VDC and use it to run R-392’s. (K1YO2K) Removed from equipment, with connecting cables and data sheet. Appears unused. Checked.
-
SM-D-969142
$75.00Battery Charger Conditioner accepts BB-490 style battery. (M1I) Used.
-
UADP-A044WJPZ
$9.99Sharp AC Power Supply/Adapter. Input: 110-240V 50/60 Hz 75W. Output: 12V 5A. Please take note 2 wire AC power cord not included and original output connector has been cutoff. (M1Y) Used.
-
PP-1097B
$125.00300 Watt DC Power Supply Input 115 VAC 60 Hz Output 6 12 24 VDC. AC Variac controls DC output. 12.5 Amps @ 24VDC 25 Amps @ 12VDC 50 AMPS @ 6 VDC. Rough Exterior Condition. Used Reparable.
-
B14L-5105-0178A
$24.50FUJITSU DENSO POWER SUPPLY INPUT VOLTAGE 220/240 VAC 3.0 AMP 50/60 Hz AC 100/115/120 VAC 6 AMP 50/60 Hz AC. Output: +5 V DC @ 11 Amps -12 V DC @ 5 Amps +24 VDC @ 5 Amps. No Documentation. (P2K) Unused.
-
HP6033A
$275.00HP6033A SYSTEM POWER SUPPLY Used Reparable
-
HCC15-3-A
$18.00Regulated Power Supply. 12VDC 3.4 amps or 15VDC 3 amps. Requires 115VAC 60Hz. Made by Power One. 9.4×4.9×3.2 (P1MO2U) Used good condition
-
GM-303
$99.50* General Microwave Model 303 Klystron Power Supply. Beam voltage variable from -250 to -400 VDC at 30 – 50 ma. Reflector voltage variable from 0 -to -900 volts at 10ua. 6.3VAC 1.5 amps. Reflector voltage internally modulated at 1000hz square wave adjustable up to 110 Volts peak to peak. External modulation via front panel terminal 100000 ohm impedance. Sinusoidal powerline frequency variable from 0 – 350 v P-P for reflector modulation. Power required 115VAC 50/60hz. Size 11.5 x 13 x 7.5 inches. 25 lbs sh. Ops manual repro no schematic. (C2L) Unused
-
Z5TX10-1
$15.00Abbott Transistor Laboratories 5 Volt 10 Amp Switching power supply. 6"x4"x2.25" 4 Lbs (K1YL2U) Unused.
-
LM-FA-20
$250.00Lambda Power Supply 19" Rack Mount 115 Volt 60 Hz input 20 VDC 16 Amps Output (E2W) Unused. 50 Lbs Shipping.
-
27091
$30.00Dressen-Barnes Electronics Corporation 220 Volt 60 Hz 3 Phase Input. 10 VDC 6 Amps 50 VDC 3 Amp Output. 12x8x7 (E2W) Unused 55 Lbs Shipping.
-
07031-94545-325-1
$45.006130-01-154-9666 Modular Power Supply by Tempo. Input 120V 60hz, Output 325VDC 100ma (D2Z) Unused
-
26859
$30.00Dressen-Barnes Electronics Corp. Regulated Open Frame Power Supply. 210-250 Volt 60 Hz Input. 20 VDC 3 Amp Output. (E2W) Unused.
-
LXS-EE-28-R-5193-1
$95.00Lambda 28 VDC +/- 5% 10A nominal power supply, 105-132 VAC 47-440 Hz input. 7 1/2 x 5 x 18 1/2, 47 lb., only one available. (S1L) Unused.
-
3V51212T9
$25.00Triple Output Acopian Power Supply. 5 VDC 6 Amps 12 VDC 1.2 Amps 12 VDC 1.2 Amps.
-
LM-220-V
$29.95Lambda Power Supply 30-60 VDC output .7 Amps 220 Volt Input. (T1L) Used.
-
LM-B36
$45.00Lambda Power Supply 36 Volts 1 Amp
-
JFS0750
$295.00Lambda 20-29 Volt 31.2 Amp Switching (Closed Frame)Power Supply Only One Available Unused
-
TXACA031
$1.50Qualcomm Wall Transformer 4.1 Vdc 550Ma Used.
-
AC-12-50
$1.5012 Vdc 50 Ma wallwart Used
-
LRS-53-5-42163
$60.00Regulated Power Supply by Lambda adjustable 5VDC +/- 5% at 5 amps. Perforated housing. Requires 95-132VAC 47-63 Hz. 8.5x5x2.5 5 lbs shipping (S1M) Used
-
LRS-53-28
$60.00Regulated Power Supply by Lambda adjustable 28VDC +/- 5% at 5 amps. Perforated housing. Requires 95-132VAC 47-63 Hz. 8.5x5x2.5 5 lbs shipping (S1M) Used
-
HP6438B-YY
$295.00HP6438B 0-60V 0-5A DC POWER SUPPLY Used Reparable
-
HP6034A-YY
$275.00HP6034A SYSTEM POWER SUPPLY 60 Volt 10 Amp Used Reparable
-
GR-300V-YY
$45.00GR UNIT POWER SUPPLY 300V 50 MA Used Reparable
-
LOS-R-24
$65.0024VDC 8.3 Amps Regulated Power Supply by Lambda. Requires 115/220/230VAC 47-63Hz. 24x7x5 22 lbs sh. (D2Q)
-
HF-75064
$19.99Power Supply with outputs of +5VDC 16.5A +12VDC 3.5A -12VDC 1A. Inputs 100-240VAC 50-60Hz. Made by Acme Electric. 10.2×5.8 x2.5 7 lbs sh. Used
-
1001932
$15.955VDC 10 amps +15VDC 0.7 amp -15VDC 0.7 amp Power Supply by Power One. Primary 115/230VAC 60Hz. On/Off Switch. Fused. 16×4.5×2.6 11 lbs sh. Used
-
SPS-2691
$75.00Large High Current Power Supply. Has three internal modules: 3 each 5Volt SPS-2688 no output current data bu fairly heavy. Power input 48VDC. Made by Trasistor Devices. 19×22.5×10.5 110 lbs sh. Used reparable
-
SPS-2678
$175.00Large High Current Power Supply. Has five internal modules: 3 each 5V 70A SPS-2599 +18V 70A SPS-2679 & -18V 70A SPS-2680 Power input 208VAC. Made by Trasistor Devices. 19×22.5×10.5 110 lbs sh. (C9O) Used good condition reparable
-
HV-G-5-OVM
$99.505 VDC 100 Amps PMC Power Mate Regulated Rackmount Power Supply Panel Meters 0-6V and 0-150A. Minimal adjustment on volts and amps. Fused. Requires 105-125CAC 60 Hz. 19×18.5×5.3 107 lbs sh. Used Operational
-
NLN8858A
$10.25Motorola NLN8858 Radio Walkie Talkie Charging Station. Charges Key Variable Loader batteries as well as the Motorola MX-300 seies MX-800 and STX radios. Output 10.6VDC 1600ma. Input 115VAC 60Hz 500 ma. 8.1×5.1×3.7 7 lbs sh. (L2L) Unused
-
HP-6522
$395.00HP 6522 HV Power Supply 2000 V 10 MA Used Reparable
-
VA15NT200
$75.0015V 2A Acopian Supply (Q2K)
-
VA12MT650
$95.0012V 6A Acopian Supply
-
A15NT200
$45.0015V 2A Acopian Supply (Q2K)
-
RB24G210
$45.0024V 2.1A Acopian Supply (Q2K)
-
VTD15-160
$69.00±15V 1.6A Dual Track Acopian Supply
-
A2NT220
$17.502V 2.2A Acopian Supply (Q2K)
-
NH-57220-YY
$195.00NH Research 57220 2 Phase Power Source (T1B) Used Reparable
-
KEPCO-1500
$95.00Kepco 1500 VDC 10 Ma Power Supply
-
GR-1264B-YY
$75.00General Radio 1264B Modulating Power Supply 200-300VDC 50mA 6.5VDC 1A Used Reparable
-
4734A-NOCORD
$6.00Motorola NTN4734A Saber / Astro Battery Desktop Charger. Output 9.5VDC 1.5A. Requires 115 VAC 60Hz. It has been tested and is in good physical condition. 6.5×7.6×3.3 6 lbs sh. LESS POWER CORD. (K2L) Used
-
NTN4734A
$12.00Motorola NTN4734A Saber / Astro Battery Desktop Charger. Output 9.5VDC 1.5A. Requires 115 VAC 60Hz. It has been tested and is in good physical condition. With power cord. 6.5×7.6×3.3 6 lbs sh. (K2L) Used
-
LXS-A-15-ZZ2
$35.0015VDC Regulated Power Supply Lambda LXS-A-15. Maximum Current at Ambient Temperature – 40 degree C at 2.4 amps 50 degree C at 2.0 amps 60 degree C at 1.6 amps and 71 degree C at 1.3 amps. Requires 120VAC 60Hz. 8 lbs sh. Unused
-
B200GT10
$167.00200v 100ma Acopian Supply
-
VA050MX120
$58.000-50V 1.2A Acopian Supply only one in stock.
-
VTD15-450
$129.00±15V 4.5A Dual Tracking Acopian Supply
-
VRB15G300
$99.5015v 3.0A Acopian Supply
-
VTD15-250
$110.00±15V 2.5A Dual Tracking Acopian Supply
-
VRB5G500
$27.005V 5.0A Acopian Supply
-
A2MT-1200
$34.002V 12.0A Acopian Supply (Q2K)
-
PS-141
$39.50* Hughes AML Klystron Power Supply for AMl-STX-141 Transmitter Power input 95 – 130 VAC Output -2200 VDC 130 ma and 6.3 vdc 1.3 amp current limited and adjustable. Meter monitors output voltage or current. 16 x 19 x 5.25 37 lbs sh. (P2E) Used with info.
-
FLUKE-405B-YY
$295.00HV Power Supply Used Reparable
-
210A-05R
$240.00Bertran 5KV High Voltage Power Supply Used Reparable
-
205A-10-YY
$240.00Bertran 10 KV HV Power Supply Used Reparable
-
GE9T63Y2280G03
$17.95HIGH VOLTAGE POWER SUPPLY input 120 VAC 60 Hz. DC outputs: -8000 V 0.25 to 1 ma +120 V 15 ma +24 V 1.25 amps +16 V 450 ma. 4×9.5×4 17 lbs sh. Some rust has output. (I8I) Used
-
G311
$10.20Enclosure 4.5" x 3.5" x 2.2"
-
K7300
$29.99UNIVERSAL BATTERY CHARGER / CONDITIONER KIT. (Recommended housing #G311) NiCd and NiMH batteries or different can be charged both quickly (52 minutes) and normally (14 hours). Usable battery voltages: 1.2V 2.8V 3.6V 4.6V 6V 7.2V 8.4V and 9.6V. Charge current: from 15mA to 750mA. Battery is fully discharged prior to charging and thus has a longer life. 3.4" x 3.1". Kit requires insertion & soldering of components! New
-
PP-6241-U
$45.00SOLID-STATE BATTERY CHARGER for silver-zinc or nickel-cadmium types. Three independent charging units with outputs 8-16-32 VDC or 0-36 VDC in o.1 V steps; 1.0 or 2.25 amps charge. With cables CX11971 CX11972 and CX11973. Reguires 115 VAC 45-440 Hz input . 11.5×13.8×11 46 lbs sh. With book (A2M) Used
-
OM-PP-7286
$10.00PP-7286 Op's Manual Repro
-
PP-7286
$99.50Ni-Cad Battery Charger will charge 6 12 24 or 28 volt sealed Ni-Cad battery capable of either fitting in the five battery holders on the front panel or attached to cables connected to the five sets of plug-in-connectors (jacks) located beneath the battery holders. Unit originally designed for batteries BB-557 BB-699 and BB-704. Requires 115/230VAC 47 to 400Hz. 9.5×11.6×13 38 lbs sh. Used
-
AC-9
$12.009VDC 130ma to 300ma AC adapter / wall warts GRAB BAG from cell phones. Set of 6
-
AC-12
$11.0012VDC 200 ma to 1000 ma AC adapter / wall warts GRAB BAG from cell phones. Set of 5
-
CER-11.5V
$2.00CERVCO AC ADAPTER 11.5 VAC 175 ma output; 6' cord w/o lugs.
-
SUN-REG-58
$12.005 V 8 A with OVP. REGULATOR MODULE from Sun supplies (pg 20) each with current limit and voltage adjust. Includes bridge rectifier filter capacitor two 2N3055 or equal and 723 regulator; 2 lbs. sh. No further info.
-
SUN-REG-124
$14.0012V 4 amp REGULATOR MODULE from Sun supplies (pg 20) each with current limit and voltage adjust. Includes bridge rectifier filter capacitor two 2N3055 or equal and 723 regulator; 2 lbs. sh. No further info.
-
MEND-REG-5V
$3.50POWER SUPPLY REGULATOR BOARD for supplies +5/-5 regulated 3 amp; up to 24 VDC unregulated. Capacitors two 15000 mf 15 V 33000 mf 30 V. 2/KBPC rectifiers two 2N6576 2/2N4441 SCR. Regulators fixed sealed circuit boards are replaceable. 7.8x6x4; 3 lbs sh.
-
SWPS-528
$10.95HEAVY DUTY SWITCHING SUPPLY outputs +5 VDC 28 amps +12 V 4 A +24 V 1.5 A from 115 VAC 60 Hz in. W/ ON-OFF switch & 16-pin Molex output connector. AS-IS complete no schematic" 2x5x13 6 lbs sh.
-
PS1558
$21.00POWER SYSTEMS SWITCHING SUPPLY outputs +5 V 7 amps +12 V 3 amps -12 250 ma. -5 300 ma from 115/230 VAC 50-60 Hz input. 7.8×4.4×1.5 3 lbs sh. Unused
-
12690
$20.00ENCLOSED SWITCHING POWER SUPPLY with 3" axial fan. Outputs +5 V 10 amp +12 V regulated 2.5 A +12 V 5 A Unregulated from 115 VAC 50/60 Hz input. P/o Wang equip. 2.6×5.1×12.5 7#. Made by Astec. Used-clean
-
A3060884
$14.00Switching Power Supply Outputs: 5VDC 21A -5.2VDC 7.5A 12VDC 4.7A -12VDC 1.5A. Each output has a potentiometer adjusting the voltage +/- 1 volt. Perforated housing with a heatsink on top. Requires 115VAC 60 Hz. Various mfg. 10.9 x 7 x 4.2 15 lbs sh. (D3AG9S) Unused
Quantity Price 3 - UP $11.5 -
SX200-81605
$12.00Switching Power Supply Outputs: 5VDC 20A 15VDC 2.5A -15VDC 1.0A 24VDC 4.0A. Housing is perforated. Requires 115/230VAC 50/60 Hz. Xentek Inc mfg. 10.9x7x4.2 7 lbs sh. (Q2U) Removed from used equipment
Quantity Price 4 - UP $9.99 -
HP-6205B
$85.00Dual DC Supply 0-40V .3A 0-20V .6A used reparable
-
LM-CC20-V
$60.00Linear Regulated Power Supply by Lambda adjustable 20VDC +/- 5% at 5 amps. Perforated housing. Requires 205-265VAC 55-65 Hz. 10×4.9×4.8 17 lbs Used
-
DR-12VPS
$10.95DC POWER SUPPLY designed for small tool rated 12 VDC @ 1.5 amp under inductive load like a motor. Output over 20 VDC under lesser loads; can be varied somewhat depending on load. Includes 6 ft AC cord; requires 115 VAC 60 Hz input; 2.5×2.5×5 3 lbs sh. Unused
-
10-4131-045
$23.0012 VDC 1.5 AMP DC POWER SUPPLY Adjustable +/- 2.25 volts. Requires 115 VAC 60 Hz; Mfg by ACDC Electronics. 4.9×6.3×3.4 7 lbs sh. (M1YN2L) Unused
-
PS-1545
$14.00EXELON DC REGULATED SUPPLY 5 VDC 3 amp and 12 VDC 0.1 amp output from 115/230 VAC 47-63 Hz input. "L"-mount; 5×5.3×2.8 4 lbs. (K2U) Unused
-
DCR40-13B
$335.00Sorensen DCR40-13B Rackmount Power Supply 0 to 40 V @ 13 A. Low-level remote sensing manual & automatic control direct & master-slave paralleling & series operation. Low ripple and noise. Fine/coarse adjustments for current and voltage. Large analog current and voltage meters Power required 115 V 50/60 hz 19x21x3.5 48 lbs sh. Used Checked
-
VFD15-50
$46.00±15V 500MA Dual Tracking Acopian Supply
-
VTD5-250
$34.00±10V 2.5A Dual Tracking Acopian Supply
-
VTD15-40
$46.00±15V 400 MA Dual Tracking Acopian Supply
-
VA5MT1200
$35.005VDC 12A Acopian Supply (Q2K)
-
VA5MT600
$21.505V 6A Acopian Supply (Q2K)
-
VA5MT510
$19.505V 5.1A Acopian Supply (Q2K)
-
VA5H2200
$35.005V 22A Acopian Supply (P2U)
-
VA5H1700
$29.005V 17A Acopian Supply (Q2K)
-
PSDC20
$69.9924VDC TO 12VDC 20 AMP CONVERTER. Compact design for in-car use. Input 24VDC. Output 12VDC. Maximum current 20 amps 1 min; 7 Amps continuous. Banana plugs. Fuse protected. New List Price $79.90; Our Price
-
SF2276-YY
$145.00NH RESEARCH 2 PHASE SINE WAVE WHEEL SUPPLY used reparable (M1C)
-
GR-1263C
$75.00GENERAL RADIO AMPLITUDE REGULATED POWER SUPPLY used reparable
-
MM-PP-638
$15.00Maintenance Manual PP-638 reproduction
-
MM-PP-6241
$17.00PP-6241 Battery Charger Manual Repro