Uncategorized

Relative carrier strength meter removed from R-390 or R-390A front panel. Reads 0-100 dB. Used good condition.

Collins mechanical filter for the IF deck of the R-390A receiver, 4 kHz bandwidth. May be branded with other manufacturer name (no choice). Used tested.

Collins mechanical filter for the IF deck of the R-390A receiver, 8 kHz bandwidth. May be branded with other manufacturer name (no choice). Used tested.

Line level VU meter removed from R-390 or R-390A front panel. Reads standard -20 to +3 dB. Used good condition.

R390DIALCOVER. This item covers the frequency readout of the R-390 and R-390A receivers and includes the cover, glass and lamps. May have minor signs of use.

RA-20 POWER SUPPLY FOR BC-312 receiver one only

RBL RECEIVER Various models may be National or WELLS GARDNER 15-600KHZ Power input 115V/230V 50-60 hz Bands 15-25Khz, 25 – 45 Khz, 45-80Khz, 80 – 155 Khz, 155-310Khz, 310 – 600 Khz. Uses 7 tubes: 3/6SK7, 6SG7, 6H6, 6K6GT, 5U4G. This radio utilizes a two stage TRF front end with regenerative detector. The used to be clear plastic over the dial needs to be replaced. Some have crazed and some has yellowed. We do not have connectors for this. Reproduction of manual available, see listing. Size 28.5 x 21.5x 17.5 high. Weight 84 lbs. Shpg Wt 93 lbs.

RC-14 RCA Receiving tube manual, original

RDR-1E BENDIX RADAR-TRANS-RECEIVER 2067157-0108

REBLING 8003 BATTERY QUICK DISCONNECT CONNECTOR NOS (EBAY CAB)

Standoff Insulator, 1.375″ L x 1.25″ Dia., Red (T1Z)

RES-200 5% 200OHMS OHMITE 6 1/2 M40F 6.5 X 0.7. NOS

RES-5000-11W 5000OHMS DAVOHM RW58V502 SIZE 1.8 X 0.35RD NOS

RES-75-100W 75OHMS OHMITE L100J75W 6.5 X 0.7 IN. NOS

SPDT Jennings vacuum relay. 26 vdc 920 Ohm coil. 1.6″ long. (H1G)

DAVEN RFB-551-73 73/73 OHM 80DB attenuation in 10, 10, 20, 20, 20 steps. BNC connector for input and output. NOS, (FR)

Type N male short barrel straight connector, originally designed for Antenna Specialists ASP-891 1/4″ heliax, usable with Andrew FSJ1-50 1/4″ heliax. Solder shield connection. Unused

RG-71G 1FT 6 IN CABLE WITH BNC MALE CONNECTORS. RG-71B is 93 ohm double shielded cable. NOS SCD784100

43 Ohm 250 Watt, 3% tolerance, by Dale (F7L)

15 Ohm 95 Watt, 5% tolerance, by Dale,

RHEO-50W-15, Single section 50w 15 ohm rheostat has cast metal casing

RHEO-50W-15-OFF, Single section 50w 15 ohm rheostat, two terminal with off position. NOS

RHEO-50W-35, Single section 50w 35 ohm rheostat screwdriver adjust. NOS

RHEO-50W-35-30-SWITCH-DUAL Two section rheostat one section 35 ohm 50W and other 30 ohm 50W has toggle switch which is actuated when rheostats are rotated.

RHEO-50W-6, Single section 50w 6 ohm rheostat has spring loaded wiper.

OHMITE Rheostat RJS50 0.5 OHM 10A NOS

RL-3 REEL used by the military to hold different types of antenna wire, guy wire, and telephone wire for various systems. The winding area is 8.5 x 2.5 inches. These are NOS and are empty. These are OD green and the handles rotate. (See Phil)

#RL28GUYROPE RL-28 REEL WITH TWO 52 FT LENGTHS OF APPROX 3/16 INCH GUY ROPE. Each rope has a clip on one end. USED (N1Z,C2U)

RED PLASTIC PROTECTIVE CAP FOR ONE INCH CONNECTOR

100K Ohm 95 Watt Dale Resistor, 5% tolerance, used,

RT-18 ARC-1 VHF TRANSCEIVER 100 TO 156 MHZ 30 WATTS CW AND PHONE. Crystal control. Requies 360VDC@135ma, 24VDC. Originally used DY-9 dynamotor. No front cover. Size 10.5 x 20 x 8 inches. Sh Wt 45 lbs. Used

RT-295 ARC-45 AM 225 – 399.9Mhz on 12 preset channels of its available 1750 UHF channels. Channel spacing 100Khz. Power output 1 watt. Power required, supplied by DY-107 (not available). 150vdc 115ma, 27.5vdc 1.7amp, 300vdc 130ma. shwt 19 pounds . used as is.

RT-77/GRC-9 Backpack Transceiver, covers 2-12Mhz AM and CW. Continuously tuned or crystal controlled. With protective grills. With cover. Very nice paint and markings. SH Wt 35 pounds. Used good condition.

RT-82/APX-6RT-82/APX-6 RADAR IDENTIFICATION SET. Receover Transmitter covering range of 950-1150Mhz. If freq 59.5/1.5Mhz. Can be converted to 1215Mhz. QST Feb 1961, June 1961, Sept 1961. 30 tubes, 6/6J6, 1 6AS6, 1 3E29, 3 6AL5, 1 5Y3, 2 3B24. 3 6A;5. 2. 12AU7. 7 6AK5, 1 2C42, 1 2C46, 1 1B40, 1 IN43, 1 IN25. VOLTAGE REQUIRED 24VDC and 115v 400-800HZ. Size 13 x 13 x 10 inches, wt 45 lbs. Nice physical condition

500K OHM CTS RV2LAYSA254A potentiometer, Shaft for knob. No hardware. UNUSED (N1U)

2.5 MEGOHM CTS RV2LAYSA255B potentiomenter, screwdriver adjust, no hardware. UNUSED (N1U)

PEC CANADA 500 OHM POTENTIOMETER 0.25 X 0.4 INCH SHAFT UNUSED #RV4SAYFD501A (N1U)

50000 OHM CTS RVSLAYSA503A potentiometer, screwdriver adjust, no hardware. UNUSED (N1U)

SIEMENS S10V-B40K275 VOLTAGE DEPENDENT RESISTOR , 350 V, 550 J, CHASSIS MOUNT. Removed from used equipment (O1U)

SB-3195 Switchboard receiver transfer between receivers aboard naval ships,  unused with manual (Q2B)

SC-B-189026 DAAB05-73-2424 BACKER PLATE FOR SC-C-189025 (C2U) used

SC-C-189025 STANDOFF SPACER FOR SC-D-189023 SUGAR SCOOP. Used on vehicle to stand off the sugar scoop from the vehicle body. NOS with hardware

SC-C-446109 brush guard for SC-D-48529 antenna bracket, unused NOS, olive drab

SC-D-425918 mounting bracket sh wt 5lbs

SC-D-446455 POWER CABLE. Used with Teletypewriter AN/VSC-3. Has the large 3pin Bendix power plug on one end and the 4 pin female power plug used on the T-195, GRC-106 on the other end. 2 foot long (C9R)

SC-DL-48676 Vehicle base mounting plate for MT1029. (C2G) used,

SC-DL-48682 mounting plate for MT-1898 R-442/VRC mounting. sh wt 6 lbs, (C6F) used

MAB ANTENNA telescoping. I think this is an early antenna and it is not in the book I have. Looks like part number SCI-66070. Most do not have a number on them that can be read. (M1Z)

SEMIKRON-240/10 rectifier stud diode 100 amp 1000 volt, probably unused- no heatsink residue compound shown (O1W)

SEMIKRON-240/12 rectifier stud diode 100 amp 1200 volt, probably unused- no heatsink residue compound shown (O1W)

SG-32/TRM-1 Signal Generator/Radio Test Set

Porcelain Side Outlet Lamp Holder Light Socket 660W 250V, 2″ high (T1Z)

SIMPSON 0-150VDC 3 INCH SQUARE METER. NOS

MINI 7-Pin phenolic turret socket with terminals for components unused (L1U)

SKT80/08D 80a 800 volt Stud Thyristor used (O1W)

SM-D-415553 6895-00-823-2835 COMMUNICATIONS CABLE 8FT . Cable is CO-18KOF(14.22) looks like it could be a CX-4723. Same connectors. Used good.

Replacement plate/grid cap test lead for military TV-7 type tube testers. Rubber booted #48 alligator clip on one end, pin plug on the other. (O2G) Unused in original packaging.

SONY ICR-1054A TAPE MACHINE MOTOR. removed from equipment

Switch SP3P indexed at 22.5 degrees. Silver plated contacts on ceramic insulator . Shaft 1/4 inch dia 0.4 inch long. NOS (M1X)

SPKR-2.25 5965-00-980-8824 R23A8 8 OHM 100MW 2.25 INCH DIA. UNUSED (C1H)

SPRAGUE 3600pF 30KV 715Q HIGH VOLTAGE CAPACITOR TWO AVAILABLE

SR-250-160 Slide Resistor by Milwaukee. 250 ohms at 160 watts. 8.5″ x 1.1″. Appears unused. (C1V)

ST-19 STRAP FOR BC-211 SCR-211. Adjusts to about 40 inches long. Usable for others. (L2Y)

TOGGLE SWITCH SPDT Momentary ST-50N AN3027-1. Made in USA. Screw terminals.

STRUTHERS DUNN 255XBXP 2PDT LATCHING RELAY. Coil 115V 60Hz. Contacts look to be at least 10AMP. A latching relay maintains contact closure even after power is removed. It requires another application of power to release the contacts. We do not have the connector base for this relay. Used (C2C)

NTE Desolder Braid/Wick, ANTI-STATIC 5FT No Clean ESD Safe Green 0.075″, 5′, New,

Switchcraft S830 IN LINE Jack for PL-68 1/4 inch mic plug as used on Collins, Drake and other transmitters. Screw terminals, NOS. (FEAT ROOM)

SWR-3349 connector, fits coaxial RF connector mini BNC.

T-18/ARC-5 2.1-3Mhz Transmitter very nice condition, no mods.

T-30/TRC-8 230 – 250MHZ FM TRANSMITTER. Uses 829B reactance modulator, 829B oscillator, 829B tripler and output. 2/6SN7 audio amplifier. Power originally supplied by PP-115 ( not available). FM 100Khz deviation, 12 Watts. Used

T-79/CPN-6 Transmitter Modulator 9310Mhz 40KW 2J48 magnetron. X-Band Beacon. Pulse width 0.5 useconds. Range 100 miles. Very heavy, best to pick up.

T1TN612 Pri: 115/230 Sec: 19v 1.75A, 25V 2A.  3.5 x 3.3/4 x 3.5 inches.  ShWt 7lbs.

TA-222 TELEPHONE CIRCUIT LINE JACK for SB-22 Switchboard

TA-326/PT TRUNK JACK for SB-22.(FEAT RM)

TC1048 12 CONDUCTOR RAINBOW RIBBON CABLE. 100FT 24AG NOS

TECALT4007 PRI: 117/234V 60HZ, SEC: 55V 2AMPS. Size 2 3/4 x 3 3/8 x 2 7/8 in. Sh wt 8lbs. removed from unused equipment.

Tektronix P6111B 200 MHz 10X scope probe. Attenuation 10X +/- 1.3% at DC, input resistance 10 Mohm +/- 1.3%, input capacitance 14.1 pF nominal, compensation range 15-35 pF, max input 300 V. Has readout pin for Tek scopes which automatically detect the attenuation factor. In excellent condition, with grounding lead. Used checked.

Tektronix TDS360 200 MHz digital real-time oscilloscope; large 7″ analog CRT with Dot, Dot Accumulate, Vector, and Vector Accumulate display modes; digital sampling at a 1 GS/s sampling rate. Two input channels with 2 mV to 10 V vertical sensitivity per division; horizontal time base 0.5 S to 25 nS. 21 automatic measurement modes, four aquisition modes, AutoSetup, waveform storage on 3 1/2″ floppy drive. Built in self test and functional test, no calibration equipment needed under normal circumstances. In excellent condition, with front panel cover. Power requirement 90-132 VAC 47-440 Hz, or 132-250 VAC 47-63 Hz. (Q2Q) Used checked.

Tempo S1 2M FM handheld transceiver made by Henry Radio (Yaesu). This was one of the first handheld transceivers on the market where the frequency was fully selectable, frequency is selected by a set of three thumbwheels and a switch on top panel, offset selected by a switch on the back. Frequency range 144.000 – 147.995 Mhz, offset +-600 kHz or simplex. No CTCSS (PL) tone encoder installed, a single channel encoder was an option but is not present in this unit. Power output 1.5W, power requirement 9.6 VDC internal battery. Battery was found to be leaking, was removed to prevent further corrosion. Unit has the optional 12-key tone pad, the optional antenna adapter (original) from stud mount to BNC, a standard BNC “rubber duck”, and an aftermarket (Motorola) belt clip. Case is in good condition, with some nicks on edges of top panel and some minor case scratches. Transceiver and antenna only, no manual or charger available. Used as is, not checked.

FIFTY (50) TURRET SOLDER TERMINAL PHENOLIC GENERAL ELECTRIC AS USED ON MILITARY EQUIPMENT Each terminal is approx 5/8 inch high above chassis, 1/4 inch diameter at base. Threaded for 6/32 nut. These are unused. (R1U)

TG-2/TG-2 TERMINAL BOARD with 15ea TM-175 nickle plated knurled binding posts on 16.1 x 3.75 x 0.2 inch thick black phenolic board. Terminals open to accept wire up to 0.15 inch diameter. Shwt 4 lbs. (O2G)

THALES 23386 1600494-1 cammo holster Fits radio approx 8 x 3.5 x 1 inch. Has velcro closure to cover keypad access approx 3 x 1.7 inches. Color light cammo. A customer has told us that this case works great for the Baofeng AR-152, which is a knock off of the PRC-152. He also mentioned that this case appears to be for the PRC-148. Used excellent (N1X)

TECHNICAL MATERIALS CORP XFK FREQUENCY SHIFT CONVERTER (J1S)

TP-UHF TERMINAL POST TO UHF as used on AB-15 for W-128 wire connection. (L1X)

TRACOR MSK VLF CONVERTER (N1C)

TRN6-6020B IERC or equal. Tube shield for 12AT7 6922 etc. Used very nice condition

TS-117 WAVEMETER 2.4 – 3.4 Ghz may be connected directly to oscillators to check output frequency and can indicate a dip or a peak as it is tuned to the frequency under test. AS-23 antenna UG-57 UG- 131 used

TS-323 FREQUENCY METER 20 – 480MHz. Fundamental frequency range 20 – 40Mhz. Power required 45VDC and 6VDC. Sh Wt 35 lbs.

TS-683 CRYSTAL IMPEDANCE METER, Radio Frequency Labs, 10-140Mhz.

Military TV-2C/U portable transconductance type tube tester. Unit will test most tubes from the 1920’s on except compactron types. Has 4-pin, 5-pin, 6-pin, 7-pin, octal, locktal, 9-pin miniature (noval), 7-pin miniature, round subminiature, inline subminiature, 7-pin transmitting, and acorn tube sockets, has test leads for those tubes requiring external plate/grid connection, roll chart is good. Panel in excellent condition, case in good condition with a few dents and scratches. With TM 11-6625-316-12 Operators and Organizational Maintenance Manual, TB11-6625-316-12/1 Test Data, and TB11-2661-1 Supplementary Test Data manuals. Used checked for operation, seems to correlate well with the store TV-7 on various test tubes.

Military TV-7D/U portable transconductance type tube tester. Unit will test most tubes from the 1920’s on except compactron types. Has 4-pin, 5-pin, 6-pin, 7-pin, octal, locktal, 9-pin miniature, 7-pin miniature, round subminiature, inline subminiature, and acorn tube sockets. The “D” model has an extra transconductance switch setting to more accurately test high-mu tubes. Unit has adapters E104 E105 and E107, two plate/grid cap connection leads, test data booklet TB 11-6625-274-12/1 in lid. This is the unit we have been using to test our used tubes for many years, front panel is worn, function switch has lost its detent ball but still works, unit is fully functional and recently calibrated, new #83 tube. Case has minor dents and scratches, one side of handle repaired with a cable tie. Used checked

5340-00-973-1732 Rubber double U-183-COVER used on PRC-25 and PRC-77 as protective dust cover for the two audio connectors.

U226 10 PIN HERMORPHIDITE CONNECTOR with HIGH CURRENT PINS. These connectors lock together. Each pin is approximately 0.15 inch diameter. Each connector is approximately 6.25 inches long and 2.75 inches in diameter and are nearly 12 inches long when connected. ShWt 5 lbs Used cut off.

U-94/U PUSH TO TALK, 6 PIN FEMALE 3476L10-6S

U-77 AUDIO BREAK OUT BOX. I am not sure of original use, but may need rewired to allow you to monitor the audio in an audio connection in some of the older GRC VRC radio systems that used the U-77 audio connector. ( M2X)

UG-636 BNC female to C male. This connector fits UG-971 to adapt the C connector to BNC cable. These look to be unused.

1/4 X 1/4 UNIVERSAL COUPLING, may not be as pictured. Used

URC-11 RT-285 emergency rescue radio. Transmits and receives on the international UHF emergency aircraft frequency 243Mhz. Telescoping antenna. 3 x 4 x 1.5 inches. YOU MUST NOT TRANSMIT WITH THIS RADIO. Used not tested. (J2E)

USB-micro-B to USB-A 2.0 data/charging cable, can connect many devices such as smartphones and tablets (not Apple devices) to a standard USB-A input, can be used in vehicles for connection to info/entertainment system or for data transfer to/from computer. Also works as a standard rate charging cable. Includes an integrated ferrite type EMI interference filter. 9″ overall length. (C1G) Unused.

USM207-DECADE NIXIE DECADE COUNTER FROM FREQUENCY COUNTER excellent to use four or six to make a clock. B5025 Nixie display number is 0.6 inches high. Includes diagram.

VARIABLE 1 – 10 Uhy INDUCTOR removed from 100 watt 2-30 Mhz tuner VARIND1-10

Volume knob, black metal with inscribed letters, fits 1/4″ shaft, set screw opening for 8/32″ not included, may have some paint chipping around edges, unused (D1V)

VRC Cable with connectors PTO6E-14-19S and BURNDY BTO6E-12-14P (same as GCU-316/U)

FEL FREQUENCY ENGINEERING LABS WDA940 WAVEMETER 0.96 – 4.2 Ghz. Type N connectors. ShWt 12.

Westinghouse R6100330 Diode 160 amp 300 piv unused (O1W)

Westinghouse 660W-600v ceramic light base, 2.5 inch diameter, 1 13/16″ high , for screw in bulb((T1Z)

Weston type 911 portable analog DC milliammeter. Front panel binding post terminals, one positive terminal switch selectable 0-0.1 mA, 0.3 mA, 1 mA, 3 mA, 10 mA, 50 mA, 100 mA; one return terminal. Large 7″ x 4″ mirrored meter face. Used, very good physical condition, checked for function, not calibrated. (N1IN2C)

Weston type 911 portable analog DC voltmeter. Front panel binding post terminals, one positive terminal switch selectable 0-1, 3, 10, 30, 100, 300 VDC; separate positive terminal for 0-1000 VDC, common negative. 20,000 ohms/volt resistance. Large 7″ x 4″ mirrored meter face. Used, very good physical condition, checked for function, not calibrated. (N1IN2C)

WATKINS JOHNSON 8410 88-500 MHZ HIGH POWER AMPLIFIER 175 WATTS. Power required 28VDC 900 watts. This amplifier was used in some sort of jammer system. More pictures on request. Heavy

WJ440-4-2 SINGLE CHANNEL CRYSTAL CONTROLLED AM RECEIVER 100 – 160MHZ 20KC BANDWIDTH. Originally fit into an EF-506B equipment frame. No other information.

XTUBE2 MYSTERY COLLECTOR TUBE. Looks like some kind of image tube approx 4.8 x 2.3 inch diameter plus glass protrusions for contacts. Conversation piece, whatever it is. (E2E)

XTUBE3 MYSTERY COLLECTOR TUBE. Looks like some kind of image tube approx 4.8 x 2.3 inch diameter plus glass protrusions for contacts. Conversation piece, whatever it is. (E2E)